Senin, 14 Januari 2019

Computer Hardware part 1


1.Power Supply:
The power supply converts the alternating current (AC) from your mains (110V
input or 220V input) to the direct current (DC) needed by the computer 2
. In a PC,
the power supply is the metal box usually found in a corner of the case. The power
supply is visible from the back of many systems because it contains the power-cord
receptacle and the cooling fan. Power supplies - often referred to as switching power
supplies, use switcher technology to convert the AC input to lower DC voltages.
2.Heat Sinks/Fans:
As processors, graphics cards, RAM and other components in computers have
increased in speed and power consumption, the amount of heat produced by these
components as a side-effect of normal operation has also increased. These
components need to be kept within a specified temperature range to prevent
overheating, instability, malfunction and damage leading to a shortened component
lifespan. Other devices which need to be cooled include the power supply unit,
optoelectronic devices such as higher-power lasers and light emitting diodes (LEDs)
and hard disks.
A heat sink is a heat exchanger component attached to a device used for
passive cooling. It is designed to increase the surface area in contact with the cooling
fluid surrounding it, such as the air thus allowing it to remove more heat per unit time.
Other factors which improve the thermal performance of a heat sink are the approach
air velocity, choice of material – usually an aluminum alloy due to its high thermal
conductivity values (229 W/mºK), fin (or other protrusion) design and surface
treatment.
The approach air velocity depends on the attached or nearby fan. When there
is no air flow around the heat sink, energy cannot be transferred. A computer fan is
any fan inside, or attached to, a computer case used for active cooling, and may refer
to fans that draw cooler air into the case from the outside, expel warm air from inside,
or move air across a heat sink to cool a particular component.
3.Case:
A computer case (also known as a computer chassis, cabinet, box, tower, enclosure,
housing, system unit or simply case) is the enclosure that contains most of the
components of a computer (usually excluding the display, keyboard and mouse). If
you are building your own computer selecting the case will be one of your first
choices to make: the type of case, its size, orientation, the number of bays you will
need etc.
Sizes
Cases can come in many different sizes (known as form factors). The size and shape
of a computer case is usually determined by the form factor of the motherboard, since
it is the largest component of most computers. Consequently, personal computer form
factors typically specify only the internal dimensions and layout of the case.
For example, a case designed for an ATX motherboard and power supply may
take on several external forms, such as a vertical tower (designed to sit on the floor,
height > width) or a flat desktop (height < width) or pizza box (height ≤ 2 inches,
designed to sit on the desk under the computer's monitor). Full-size tower cases are
typically larger in volume than desktop cases, with more room for drive bays and
expansion slots. Desktop cases—and mini-tower cases designed for the reduced
microATX form factor—are popular in business environments where space is at a
premium.
Major Component Locations:
1. The motherboard is usually screwed to the case along its largest face, which could
be the bottom or the side of the case depending on the form factor and orientation.
2. Form factors such as ATX provide a back panel with cut-out holes to expose I/O
ports provided by integrated peripherals, as well as expansion slots which may
optionally expose additional ports provided by expansion cards.
3. The power supply unit is often housed at the top rear of the case; it is usually
attached with four screws to support its weight.
4. Most cases include drive bays on the front of the case; a typical ATX case includes
a 5.25" bay (used mainly for optical drives) and 3.5" bays used for hard drives,
floppy drives, and card readers.
5. Buttons and LEDs are typically located on the front of the case; some cases include
additional I/O ports, temperature and/or processor speed monitors in the same area.
6. Vents are often found on the front, back, and sometimes on the side of the case to
allow cooling fans to be mounted via surrounding threaded screw holes
4.Motherboard:
The motherboard is the key circuit board holding the essential processing parts of a
computer. It allows all the parts of your computer to receive power and
communicate with one another. It is usually screwed to the case along its largest
face, which could be the bottom or the side of the case depending on the form factor
and orientation. The form factor describes the shape and layout of the motherboard.
It affects where individual components go and the shape of the computer's case.
Attached directly to the motherboard are the CPU, RAM, expansion cards,
networking, video, and audio components.
ATX (Advanced Technology eXtended) is a motherboard form factor specification
developed by Intel in 1995. A full-size ATX board is 12 × 9.6 in (305 × 244 mm). It
was the first big change in computer case, motherboard, and power supply design in
many years, improving standardization and interchangeability of parts. The
specification defines the key mechanical dimensions, mounting point, I/O panel,
power and connector interfaces between a computer case, a motherboard, and a power
supply. The specification has been revised numerous times since 1995, the most
recent being version 2.3, released in 2007.
Standards: ATX, standards for smaller boards: microATX, FlexATX and mini-ITX.
5.Expansion Cards:
Special expansion cards are one way to add new types of ports to an older computer
or to expand the number of ports on your computer. Like other expansion cards, these
cards clip into an open expansion slot on the motherboard.
6.Video (Graphics) Card:
A dedicated video card (or video adapter) is an expansion card installed inside your
system unit to translate binary data received from the CPU or GPU into the images you
view on your monitor. It is an alternative to the integrated graphics chip.
Modern video cards include ports allowing you to connect to different video equipment;
also they contain their own RAM, called video memory.
Video cards also come with their own processors or GPUs. Calls to the CPU for graphics
processing are redirected to the processor on the video card, significantly speeding up
graphics processing. Updating to a dedicated graphics card offloads work from the CPU
and system RAM, so not only will graphics processing be faster, but the system’s overall
performance will improve.
The video card also controls the number of colors your monitor can display. The number
of bits the video card uses to represent each pixel on the monitor (referred to as the bit
depth) determines the color quality of the image displayed. The more bits available, the
better the color detail of the image.
7.Sound Card
 Sound cards attached to the motherboard and enabled your computer to record
and reproduce sounds.
 Most computers ship with a basic sound card, most often a 3D sound card. 3D
sound is better than stereo sound at convincing the human ear that sound is
omnidirectional, meaning that you can’t tell what direction the sound is
coming from. This tends to produce a fuller, richer sound than stereo sound.
 To set up surround sound on your computer, you need two things: a set of
surround-sound speakers and a sound card that is Dolby Digital compatible.
There are many formats to choose from such as Dolby Digital EX, Dolby
Digital Plus, and Dolby TrueHD.
The ports on the sound card allow you to connect additional audio devices such as
amplified speakers, headphones, microphones etc.
Thank you.

Share this